militec1

[Guest Jamesmb]

Not sure if this is the right category or maybe should be under gunsmithing & troubleshooting, but I have a revolver and had been using Outer's tri-care for cleaning, lubricating, and protecting and using Kleen Bore gun cleaning solvent no. 10 to get crud out if needed but heard alot of good things about militec1 and was wondering about its application and if anybody has used it. Is it only for lube? Just wondering what everybody uses besides these?

[TripleDigitRide]

Not sure if this is the right category or maybe should be under gunsmithing & troubleshooting, but I have a revolver and had been using Outer's tri-care for cleaning, lubricating, and protecting and using Kleen Bore gun cleaning solvent no. 10 to get crud out if needed but heard alot of good things about militec1 and was wondering about its application and if anybody has used it. Is it only for lube? Just wondering what everybody uses besides these?

That is just about all I use. Yes, it's a lube, but it also makes cleaning much easier.

Militec1 is heat activated, so you should apply it, then fire a handfull of rounds to bring the weapon to operating temps. I usually apply a second and third coat after several rounds. After you complete this process, the militec has become impregnated in the metals, and thus acting as a dry lubricant.

[Guest Jamesmb]

Hi TripleDigitRide

So after the final firing, do you wipe all the militec1 off and keep the gun dry? I guess that is what I am asking, when I use the Outers I keep a light coat on after cleaning to help protect, just wondering if I should apply that afterwards or not.

[TripleDigitRide]

I always keep a light coat after cleaning. A very light coat. Unlike many lubes, Militec doesn't wear off near as fast. Even after the "wet" part of the lubrication is gone, it's still working due to the fact that it's a dry impregnated lubricant.

Check out the info on their website. There's some very good info.

[jay1313g]

I use Militec 1 on every firearm that I have. It is like Slick 50 for guns! It made a world of difference with my Warthog and P3AT. I could tell the action was much smoother after applying it.

I clean the gun thoroughly and then clean any solvents off with alcohol. Next, I apply the Militec 1 and heat it with a hair dryer. I will reapply and add heat usually 3 times depending on how much time I have.

This is what has worked well for me! Let me know if you have any other questions and good luck!

[TripleDigitRide]

I use Militec 1 on every firearm that I have. It is like Slick 50 for guns! It made a world of difference with my Warthog and P3AT. I could tell the action was much smoother after applying it.

I clean the gun thoroughly and then clean any solvents off with alcohol. Next, I apply the Militec 1 and heat it with a hair dryer. I will reapply and add heat usually 3 times depending on how much time I have.

This is what has worked well for me! Let me know if you have any other questions and good luck!

I'm glad you mentioned the hair dryer method. I forgot to mention it.

[Guest Jamesmb]

Will a hair dryer get hot the gunmetal hot enough? I read somewhere on the web somebody put his gun in a toaster oven about 200 degrees. So far I put it on before I go the range, then when I get home, I wipe clean with a cloth, no oil, and before I go the range again, maybe the next day I put some more militec 1 on. I guess though the three heating cycles should be one after the other, so as not to let the gun cood down?

[jay1313g]

The hair dryer will get it pretty stinkin' hot!!!! Be careful picking it up.

[TripleDigitRide]

Will a hair dryer get hot the gunmetal hot enough? I read somewhere on the web somebody put his gun in a toaster oven about 200 degrees. So far I put it on before I go the range, then when I get home, I wipe clean with a cloth, no oil, and before I go the range again, maybe the next day I put some more militec 1 on. I guess though the three heating cycles should be one after the other, so as not to let the gun cood down?

Yes, a hair dryer set on high will get hot enough. You don;t need to exceed 150 degrees.

When a gun is new (or new to me) I take it to the range with some Militec. I apply it to all moving parts and inside of the barrel, then I shoot 2 magazines. I apply more Militec, and shoot 2 more magaines. I then do it a thrid time.

I apply a very thin coat after cleaning. I will repeat the above process every few thousand rounds. Militec claims that you can shoot roughly 1500 rounds without applying any more Militec1, but because I always leave a thin layer of oil after cleaning, I pay little attention to that.

Here is some info from their page. Read through it.

FIREARMS APPLICATION INSTRUCTIONS: SELF-LUBRICATION

CHARACTERISTICS: MILITEC-1 Synthetic Metal Conditioner has the unique ability to create a complex, molecular compound within the surface of heated gunmetal. This causes MILITEC-1 to become part of the metal, not merely a temporary coating or a boundary film. There are two main characteristics of this safe new compound. First, it seals and conditions the metal by stiffening (not hardening) the metal surface. Second, it makes the gunmetal self-lubricating under all environmental conditions.

SELF-LUBRICATION: After a complete application, a MILITEC-1 conditioned firearm is self-lubricating. Self-lubrication gives the firearm's gunmetal the dry lubricity that is required for sustained fire under all environmental conditions. If exposure to dust, sand, or extreme cold is a concern, all excess MILITEC-1 must be wiped away, leaving the firearm's surface metal clean, dry, and constantly lubricated. Please note: Complete corrosion protection and self-lubrication is attained only after both Step One and Step Two (below) are completed.

PREPARATION: To take full advantage of MILITEC-1's unique properties, start with a clean firearm. Although MILITEC-1 contains a mild detergent that will help with subsequent cleaning, there are no solvents or other hazardous materials in MILITEC-1, so it cannot remove old caked-on fouling and build-up from other lubes. Thus, if a firearm is dirty, you must clean it with a solvent before you proceed. Normal fieldstrip cleaning should be perfectly adequate. If possible, remove the handgrips, clean and prepare.

INITIAL TREATMENT: Applying MILITEC-1 to a firearm for the first time is a two-step process: (1) Application and (2) Firing.

STEP ONE: APPLICATION. Now that the firearm is clean and dry, apply a light film of MILITEC-1 to all surfaces, including the bore. Burnish/polish MILITEC-1 into exterior surfaces by rubbing rapidly using a cloth lightly dampened with MILITEC-1. Sparingly apply drops into the action, concentrating on springs, moving parts and metal-to-metal contact areas. If your firearm has a magazine, be sure to apply MILITEC-1 both inside and out. Leave a very light film of MILITEC-1 on all surfaces during reassembly. Now proceed to Step Two.

STEP TWO: FIRING. Once you fire your weapon enough times to reach operating temperatures, the heat and friction will activate MILITEC-1, strengthening the bonding process that was started in Step One. While firing, MILITEC-1 creates a self-lubricating, water-repelling, dry compound within the gunmetal.

Additional Application Instructions: If Step Two is not immediately possible, consider applying low heat to the firearm to facilitate the bonding process until you can perform Step Two. In field conditions, place your lubed firearm in the sun underneath black plastic or a similar ventilated heat source for at least two hours. Alternatively, you may use a heat gun, hairdryer, burnishing or polishing tool to heat the gunmetal. In heat controlled environments, do not exceed 150° F (65° C). In all applications that require heat to condition the firearm, always insure proper ventilation and wear protective clothing. Please consult our MSDS for additional information.

ULTIMATE PROTECTION: To maximize the effects of MILITEC-1, repeat Step One and Step Two while the firearm is still hot from the first firing session. MILITEC-1's impregnated molecular bond intensifies during the next 2-3 applications on hot gunmetal. MILITEC-1 has now become a physical part of the gunmetal.

SUBSEQUENT APPLICATIONS: It is important to continue using MILITEC-1 to lubricate your firearm throughout its normal service life. Consistent use of MILITEC-1 will maintain the self-lubricating effect, maximize corrosion protection, and minimize wear on all friction surfaces. Fouling, deposits and metallic debris do not adhere as easily to gunmetal surfaces conditioned with MILITEC-1. Use a safe, inexpensive cleaner or solvent to detail the firearm, if necessary. For maximum corrosion protection, and especially if long-term storage is anticipated, leave a very light film of MILITEC-1 on all surfaces, after both steps or field application procedures are completed.

APPLICABILITY: MILITEC-1 is recommended for all pistols, shotguns, rifles, automatic weapons, tank guns and artillery of all calibers and sizes. Note: MILITEC-1 will alleviate jamming due to tight tolerances.

[bobmack]

hi,

just for the record, --- if you go to their website and request it, they will send you a free sample in the mail.

great product.

bob

[RWF]

we have use it for a few years now and happy with it