Jump to content

radiator leak help


laktrash

Recommended Posts

Posted

I have a leak in the radiator of a GMC yukon, can't pin point but seems to be some where behind the fan shroud. I plan on trying some alumaseal stop leak. My question is the dirctions say to turn on the heat before starting the process, but if the leak's not in the heater core is it necessary to do this. I'm really not big on trying this but it's an older car and trying to spend $5 to save $500. I just don't see the need to run this crap thru the heater core if I don't need to.

  • Replies 17
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted

If it's a small leak, I'd suggest you try putting a can of black pepper in the radiator before trying the stop leak. If you use the stop leak, I would suggest you follow the directions on it. It's going to get in your heater core anyway the first time you do turn on the heater.

Posted

Can you not get the shroud off and find the leak? A little silver solder will fix small leaks with ease. I've heard JB Weld works too. I'd avoid the "stop leak" stuff.

Posted

Do not use stop leak or pepper!

It will sometimes stop or slow a pin-hole leak.... but it will also clog-up your radiator tubes and heater core.

The price to have a new heater core installed, have your radiator "rodded" and system flushed when your engine starts overheating will be more expensive then just buying a brand new radiator now.

My suggestion is to remove the radiator yourself, take it in to a radiator shop and have them repair it. A radiator shop can easily solder an aluminum core or replace the plastic tanks.

Posted

+ a whole bunch on avoiding any "Stop Leak" product. That stuff will kill a radiator!

Posted
Do not use stop leak or pepper!

It will sometimes stop or slow a pin-hole leak.... but it will also clog-up your radiator tubes and heater core.

The price to have a new heater core installed, have your radiator "rodded" and system flushed when your engine starts overheating will be more expensive then just buying a brand new radiator now.

My suggestion is to remove the radiator yourself, take it in to a radiator shop and have them repair it. A radiator shop can easily solder an aluminum core or replace the plastic tanks.

This :rolleyes:

Posted
Do not use stop leak or pepper!

It will sometimes stop or slow a pin-hole leak.... but it will also clog-up your radiator tubes and heater core.

The price to have a new heater core installed, have your radiator "rodded" and system flushed when your engine starts overheating will be more expensive then just buying a brand new radiator now.

My suggestion is to remove the radiator yourself, take it in to a radiator shop and have them repair it. A radiator shop can easily solder an aluminum core or replace the plastic tanks.

This is very good advice.

Posted

Well I realize what your saying about nostop leak but its got 160,000 miles on it and its kinda of a back vehicle it wifes old car that she had before she got a murano. Not playing the "poor me" card but my health doesn't allow me to do any mechanicing on my own. My step son borrowed it and when i got it back it had the leak and has just been sitting and was looking for cheap patch. I worry about moving around for fear the dogs might get into leaking anti freeze.

Posted

Stop Leak or pepper is meant more for an emergency only type fix. Meaning is you develop a leak and need to get to a safe location or to get back home. These products may offer enough of a fix for that to happen. I would not use it in place of properly fixing the radiator.

If It was me I would put some black pepper in there and see what it does. But you will need a proper repair.

Posted

Call 1-800Radiator. Im sure the price of the radiator isnt as bad as you think. I bought one last year for a Ram and is was $140 shipped to my door the next day.

Posted (edited)
This is very good advice.

Didn't mean to poop on your elephant.

The problem with stop leak (and the ole' pepper fix) is that it was designed to work with radiators of years past.

Modine pretty much reinvented radiator technology some years back and now every car uses their design. Radiators of, say 20 years ago, are much different then today. Today the tubes are pretty much just barely wide enough to allow water to flow. Adding anything else into the system will clog them quicker then this fat boy can eat a Hershey bar.

Course, stop leak can work for an emergency situation, but I still wouldn't recommend it as you're looking at a mess to clean up later =$$$. I'd just as rather drive with a leak.

If stop leak does have to be used, then drain every drop of coolant from the radiator, then add the stop leak to the drained coolant, mix well, then slowly refill the radiator with the engine running. This will help keep the stop leak from lumping up in the system. Same idea as sifting your flour before baking a cake.

Well I realize what your saying about nostop leak but its got 160,000 miles on it and its kinda of a back vehicle it wifes old car that she had before she got a murano. Not playing the "poor me" card but my health doesn't allow me to do any mechanicing on my own. My step son borrowed it and when i got it back it had the leak and has just been sitting and was looking for cheap patch. I worry about moving around for fear the dogs might get into leaking anti freeze.

Even letting a radiator shop do the removal and install, you're still looking at a cheap fix. Good thing about GMs is the radiator comes out in 5 minutes.

If push comes to shove, just drain the coolant and refill with pure water. Only problem with water only is your water pump will suffer without the lubricant that's added to coolant.

Edited by strickj
Posted

i have used JB Weld stop leak on one of my tractors. it worked for one year, then gave way. other time that i have tried ant stop leak it did not work.

Posted

I would call around on a new or used radiator, your going to have to drain it either way , it only takes a few minutes of minor work to swap the radiators in a yukon. The whole swap should take less than 30 min. Plus even with the used they will have some kind of warranty.

Posted
Didn't mean to poop on your elephant.

The problem with stop leak (and the ole' pepper fix) is that it was designed to work with radiators of years past.

Modine pretty much reinvented radiator technology some years back and now every car uses their design. Radiators of, say 20 years ago, are much different then today. Today the tubes are pretty much just barely wide enough to allow water to flow. Adding anything else into the system will clog them quicker then this fat boy can eat a Hershey bar.

Course, stop leak can work for an emergency situation, but I still wouldn't recommend it as you're looking at a mess to clean up later =$$$. I'd just as rather drive with a leak.

If stop leak does have to be used, then drain every drop of coolant from the radiator, then add the stop leak to the drained coolant, mix well, then slowly refill the radiator with the engine running. This will help keep the stop leak from lumping up in the system. Same idea as sifting your flour before baking a cake.

Even letting a radiator shop do the removal and install, you're still looking at a cheap fix. Good thing about GMs is the radiator comes out in 5 minutes.

If push comes to shove, just drain the coolant and refill with pure water. Only problem with water only is your water pump will suffer without the lubricant that's added to coolant.

You are exactly right, I was just answering his question about a "cheap fix" to try. I'd pull it and have it repaired were it mine.

Posted

Before you do anything make sure the leak is in the radiator. The weep hole in the water pump is in that area and the drips from that may mimic a radiator leak.

Posted

Stay away from stop leak type products. Fix it right the first time! Those spring loaded clamps lose the strength after a while. try and find USA made screw type hose clamps. could be a split or pin hole in a hose as well. also the drain petcocks sometimes get a leak when the O-ring breaks or deteriorates.

Many GM V shaped motors blow intake manifold gaskets. make sure you're not losing coolant there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

TRADING POST NOTICE

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions.

TGO makes no claims, guarantees or assurances regarding any such transactions.

THE FINE PRINT

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

TNGunOwners.com (TGO) is not a lobbying organization and has no affiliation with any lobbying organizations.  Beware of scammers using the Tennessee Gun Owners name, purporting to be Pro-2A lobbying organizations!

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines
 
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.