xtriggerman

A buddy of mine wanted to get an old rolling block carbine back into the woods but the bad 43 cal barrel had to go. The gun had been reblued at some point and the internals were not molested at all from their original Remington factory fit & function, so it was a fine candidate for a 45-70 conversion. I told him to pick up a nice Ebay barrel at some point and he did just that with the purchase of a Ruger #3 45-70 barrel that was a mint factory take off. I told him the big RB receiver ring can "sleeve in" about any factory barrel from what ever. So, In this shot, what you see is the original square 12 TPI shank cut off and taped with a 15/16ths x 16 TPI internal thread. Once that was done, the Ruger .900 OD 16 TPI shank was turned down to .875 and then lathe turned treads to a hand fit zero wobble fit to the old shank bushing. The trick was to set the old shank extractor cut to clock right in the receiver while at the same time, the Ruger barrel sights clock at 12:o clock over the receiver. Once the proper bushing position was set and marked, The bushing gets JB welded to that exact spot. Then the shank gets the breach block clearance cut and extractor cut via the original shank cut position into the Ruger steel. Here the extractor has been mig welded to its needed extra length after the original chamber was deepened to perfect head space. The cold blue still shows the slight face line of the Ruger barrel in the core of the original shank face. A 1976 made Ruger tube.... A Fun project with great results. Now, only a practical scope set up has to be done. I'll add that picture once I figure something out for his 2.5x fixed Leopold. Gotta Love the way that 300g Rem JHP nudges the shoulder in this ol girl!

Its pretty bad in NY. Getting a permit in general is not that much different from an enhanced here aside from the added 4 personal signed reference friends that write a few lines of your "character" description. The only issue for Hunting, target shooting or self defense also must show a Hunting License, Range membership or a security job of sorts for the unlimited. If thats not bad enough, the county judge can restrict the number of handguns you own by not approving another handgun purchase since you need a judge signed "purchase coupon" to buy another handgun. I remember having to write a required essay to the county judge explaining why I wanted to buy another pistol. That was the lowest point in my life in the kissing ass department I have ever endured. NYS is a prize lap dog of the same deep state handlers that installed Biden. Be ever watchful of Davidson and Shelby counties and their spread into other places of congestion. We will see who on the SC has been infected with deep state sublime cool aid.

When I had a GS in NY a buddy of mine told me about a retired NJ State Police Lt. that retired to Newburg NY with a gun parts business. He said he saw his shop & talked to the guy. Apparently, this Lt was in charge of all stolen firearm recoveries in NJ and was tasked with destroying them as per BATF regs. So he destroyed the gun's SN frames and "discarded" the remainder into his personal trash can. Needless to say, he had everything from Luger parts to God knows what all for sale out of his NY shop. Giving guns back to owners dosent have to be a catering service especially in those places that dont believe in the 2nd as a rule. Besides how do you think these guys get parts? Gun parts kits. Home of EveryGunPart.com

Look at it this way..... A "channeler" could use it, since apparently Wayne was fond of it to hook up the new owner with a personal interview! Ha,Ha...... LOL ! For those with more money than God....

Send me the mag, I'll button it for you. I made one up for a 9mm luger a couple years ago. That picture Jeb 48 was kind enough to post is all the spec I would need. We had a pretty good chat when you and your Pilot buddy were over. Tell him I said hi.

Didn't you and a friend of yours come over once for a little wrenching on a 22 hornet or something like that a while back?

Great project. The bulk of those guns were JC Higgins guns made by High Standard. The butt shield is a dead give away for the HS brand. Those 22's were actually a really good design. The cartridge guide blocks were solid steel halves with a snappy working cartridge lifter/carrier. This High Standard gun was at the top of its 22 auto game in its day unlike the jam-o-matic Steven/Savage 187 series autos. The only flaw in this design is the fact you can't see the the follower threw the open action to see if your empty. If the tube gets dirty or it has a weak spring in it, working the action several times may produce a "ghost" round into the chamber! All ways pull the inner tube out and work the action to insure its unloaded if your inner tube feels a little weak. Good luck with it. I'v had one for 44 years.

For what there worth?.... Numrich has Triple K's Stoeger Luger Parts for Sale | Gun Parts Corp.

Kahles are about as tuff as they come. Back when Dave at Del Sports in Margretville NY was the sole importer, he shown me a Kahles that had a massive dent in the tube forward the turret. He said the guy dropped the gun on a rock hunting and the thing was still zero'ed! Back in those days they were a cheaper (if you can call it that) alternative to its kissin cousin Swarovski. IDK about these newer electro ones but they were top shelf in Glass for a very long time. Good Luck with yours.

That looks alot like this Kyber 303 I bought a number of years ago at the Knoxville GS. They were hot on putting that distressed finish on the guns its even under the forend wood where as there should be a defined difference between the exposed and covered barrel finish. The darn thing even shoots but the chamber is so pitted, I had to knock the brass out with a cleaning rod. And no, I didn't hold it to my face when I pulled the trigger! Still plan on hanging a 45-70 barrel on it some day. Good Luck getting it completed.

Congrats Greg.... If I didnt have so much to do in being retired, I would seriously consider buying a good quality stock duplicating machine and just crank out semi inlet stocks of various kind. Nice manlicher type stocks can bring a premium even in semi inlets. Heck I bet your dad might even enjoy shaving some close tolerances on it! The few that do stock copies are normally backed up at least 6 months just on orders. But I would just cut enough to fill a couple gun show tables and be done. Think about it. If you get too bored, its a fun hobby with $$$ benefits. A good machine would run you between $3500 and 4K to start.

My 2 cents.... This gun does not have honest ware on it. Clearly, some one has all ready sanded the original finish off by a quick glance at it. Thats a HUGE consideration in this project. Sadly Gf54 is right in his assessment of what passes for a reblue from buffing wheel hacks. That has been true for ever. I did Hot bluing of blued & Stainless guns for over 10 years and it is definitely a talent in knowing how to keep a radius curve and a flat flat and equally importantly, the defined edge between them. In gunsmithing school, we spent alot of time on exactly what a factory blue consisted of in metal surfacing and how to reproduce the same. Just the variety of high quality belt sanding belts needed is no small change along with at least 4 buffing wheel types and grits as pictured. Normaly I would agree to keep it as is but its not original patina by any stretch of the imagination along with the pitting coverage. If the gun has a good clean bore and is in good running condition, I would do it if it were my gun as long as you find a reputable smith that specializes in restorations. The trigger guard could probably be black ceracoated maybe? I never did that stuff. If I ever get retired from retired...... maybe.

Now thats a serious woods hammer! The checkered walnut was way, way too long in coming Marlin. Now the thing I like about the regular 1-5 scope is the fact that little scope gives you 81' at a hundred yard of view. Basically no magnification at all on one power. There has been a few times when one step or slight move scattered a number of deer in a general direction and the low to no power was able to make a fast determination on all their sizes because they were all still in scope view. Dropping the biggest one when they stopped & turned around to look (as doe's do), pretty much convinced me on that particular set up. I admit tho, I never put a scout scope set up in the woods but with my bifocaly odd glasses, not sure it would work for me.

Thanks for the ! out of 28 views, must be no one likes the idea of a gun like this. At least the folks here got me into joining TFA. Alot of good discussion there that I can rely on. Gun story tellin.... not so much! lol

A while back when everygunpart still had a bunch of Marlins coming & going, I grabbed a straight stock 30-30 on one of their one day sales. I thought I would build a light weight 336 some day once a stripped receiver came across my path. That day came.... sort of a few weeks ago on GB when a guy sold me an early 1950 336A 24" bl in .35 that was mostly stripped save for the lower tang, trigger & loading gate. Found a 35 bolt on Ebay and then once the 35 was in my hands, I found the reason for the dumping of it. Some Gun smith??? drilled and taped the receiver but ended up with off center holes just enough to have a problem getting a scope to zero in. The thing with tapping a non taped 336 and older was the ceiling of those receivers have a arched cut nearly half way across the ceiling of the receiver top. 2 of the dead center holes actually cut threw into that open slot that is where the lever sweeps up threw the bolt. Once a drill breaks the very surface, it quickly wants to move into that empty space and thus, bores the hole over to the right where there is hardly any resistance. Luck for this receiver, the guy didn't use the newer 8-40 base screws of a regular Marlin but some odd ball 6-40 screws. This allowed me the room to mill the small holes over in the mill just enough to over bore them with 8-40's of the weaver base and be damn near dead on straight! All tho he also drilled a 5th hole in there that was beyond help. Then for some ridiculous reason, someone extended the forend tip dove tail more than 1/8th forward so nothing would fit it. So much so, it was clearly visible sicking out beyond the wood! WTF..... well, I cut a new wide dovetail blank and friction fit that one and a second one up where you see the front barrel band. Both got belt sanded down to barrel OD and sand blasted & cold blued to pretty much match the matt finish that was on it as received. The pistol grip lower tang got a trim job that matched the straight stock yet kept the G300XXX SN in place. I'v read the cast bullet shooters love these pre micro groove barrels. I cut & crowned to 16.5" Trapper style. Makes for a good small critter gun with cheap lead loads. Any way, I topped it with new irons and a pretty decent China Spina 1-5 scope that has surprisingly nice glass. Originally, I would keep this since its as nice as an old meat gun comes but last week I closed on a pasture lot auction that is adjacent to my 13 acres giving me 30 and extending my back 410' against the state park land another 411'. Needless to say, I walked out of the closing with my pockets turned inside out. I'm dumping some guns these days that normally would have been traders or value makers. The last time the pasture lot was for sale was 1946. It was a total of 78 acres and the tax on it was only $680 bucks. Needless to say... a once in a life time buy for me and now puts me in green belt tax catagory for what I will keep out of the new 17 acre addition. Funny thing is the land auction closed 9 days before I collected my first SS check! If it wasnt for that new found cash..... the land buy would not have been possible. Compared to my 20.5" barreled model 36 30-30

Stealing is more genetically predisposed in some folks than others depending on the "health" of our social climate. Then there is all ways the ones who do it just because they can since they are well off to begin with. 25 years in state prison has taught me swift and harsh punishment will infact real in the numbers of crimes committed. The majority of inmates in prison are scared nearly to death of being hit with a tier 3 ticket that will put them in keep lock status for any length of time. That is 23 hours inside a self contained cell with one hour out in a rec area alone that is a 12 x 15 foot area, 12 foot high brick & block walls with razor wire around the top edge. A Book or a hand ball is allowed for the hour. The only movement he would see during that time is maybe a plane or bird fly over his sky window or the CO looking in on him threw his rounds window in the door. This is what is in place of the old world corporal punishments of the old warden days. The liberal courts have yet to rule this is cruel and unusual punishment. I tend to think totally ruling out corporal punishments was a mistake. Physical pain as a learned process of the brain (hand in fire) tends to stay more so in the for front of the thought process rather than a bout of "maybe" mental anguish that has yet to be experienced. Such as the mention of the 50's lack of steeling of things in rural areas. Getting the tar beat out of you and not having a single recourse of retaliation toward the beater for ones crime was a stable of the street. Today, the attorneys and courts have money to be made from defending a criminal if you can pony up a good argument during the $$$$ exchange process. The pendulum has swung way to far to the left putting $$$$$$$$ above everything else. Right or wrong has no standing since those accounts are over drawn. What would a Monkey do if another monkey stole his machete?

The answer from the Speaker..... Thank you for the email. Simply sending a letter to Governor asking him to do something isn’t action or a solution in my opinion. It’s passing the buck. We will go back in session in January and legislators can actually file legislation that is meaningful and has more authority than a letter. I will put my second amendment voting record up against anyone anytime. I appreciate you reaching out to me. Sincerely Cameron January? I gotta get a job like that! 4 months to think about what they should or shouldn't do. Yah gotta love politics....... LOL

I had to buy Frontier from the git go. now its been nearly 7 years and with the 12mb upgrade, its not been bad but does go down on occasion. The CS on it sucks tho. They dick you around alot before they will just replace a bad modem. I watch mostly off a fire stick off the router modem and havent had too many buffering issues on the movies. I have Verizon phone now but T-mobil serves this are the best and I might switch soon to it. My Brother in law moved here to Crossville a couple years ago from Glouster VA and they love it here. Hes retired Army. Thanks for your Service. May God help the kids thinking about it. I'm retire NY Corrections with a professional Gunsmith back ground. If you need an at the moment wrench over one of your hammers, hook up. I'm right next to the Cumberland mtn State Park. We share many of the same social principals.

Both mine ducked this one. My Email to both..... To the Honorable Rep C. Sexton. It is with deep regret that I did not see your name on Rep Clay Dogget's letter of 2nd A abuses by the Feds to our Govenor. I moved my Family here from upstate NY 7 years ago hoping the Republicans here in Tennessee say what they mean and mean what they say. This letter clearly stipulates the conditions of federal abuses that are now being contemplated on top of an over regulated bureaucracy that should have been reeled in as President Ronald Reagan did by slashing their funding due to 2nd Amendment civil abuses. Being in Crossville my self, Please feel free to stop by and chat about your reasoning in defending the course the BATFE is set on. Thank you for your time and consideration.

Just looked at the CMP web sight and the Criterion barrel they have there looks like a very nice repro. Iv used that brand on the M1 and its a great OEM duplicate of what came on the gun. 2 bones is a great price also. If they are in stock, thats like an early Christmas gift to ones self!

I'v done a number of P14 barrel jobs and the barrels happen to be on very tight. The action wrench is a basic one but its the barrel collet that has to be a perfect barrel contor match to be able to brake the action free without spinning the barrel in the collet and then there is all ways the possibility of crushing the bore despite the contor collet simple because of the crazy tension the barrels are put on with. good thing is most dont want the original barrel so clamping the pee out of it to keep it from spinning is not an issue. Here are a few of the barrels I saved since they have good bore and can be repurposed for other 303 / x39 projects. The biggest issue I think on these 14/17's is no one makes a proper blank for them. The action requires a 1.320" OD to shoulder the receiver as the originals. The largest you will find is 1.250 on a unturned blank, and most are not even that large. Most smiths will just give you a barrel of that diameter to shoulder up and be done with it. Just be sure you get at least a 1.250" shouldered barrel. Its not going to be mil spec but those guns were a bit over done here & there in specs. What do you want to barrel it with?

I gotta hand it to some of these TN natives. This guy had to be way, way up there in meth land in this police account. The meth heads around here never cease to amaze! Cookeville Man Seriously Injured After Severing his Penis Before Leading Officers on Pursuit - WJLE Radio

Oh, one other thing. a sticky disconnector is usualy a poor engagement of the disconnector spring on the disconnector. When I work a 1911 action, the middle finger on the spring all ways gets a wheel buffted polished bevel where the disconnector rides up and down off of it. Factories dont do this. Also the bend in that spring must be just right for proper diconnector function. A slicked up 1911 will hardly show any hang up what so ever when hand walking the slide over it. A one minute buff with a 220g then 400g wheel will do wonders in taking the stall out of it.

Since I interjected myself into this, the area of concern on a 1911 if someone has the habit of free slamming the slide home on an empty chamber is primarily the barrel link pin hole and barrel link. These two areas will see ware before anything else. Mil spec on the barrel pin hole was originally a press in fit AND a prick punched hole rim into the pin edge on both sides. This was in case the pin became loose it may still be kept from drifting into the frame cut that shoulders the barrel pin in place. The link can stretch and mostly the barrel will batter the slide stop pin, opening up the tolerances in the frame holes since the frames are not hardened by any significant means. Unlike the slides that must meat a hardness specification. The majority of slide stops today are all castings and clearly not as durable as the OEM hardened forgings. There for, the slamming will result in ware on the barrel pin hole, barrel stop legs where the barrel stops hard in battery on the slide stop pin and some what on the link its self along with the slide stop. Mind you barrels are not all that hard and subject to some peaning if repeatedly battered in a dead metal to metal show down as free slamming. When I went to gunsmith school 79-81, we got all our info from books, not internet sound bites. Too much of that going around these days.