zombiehugger

fde 20 fde 23 od 27   Never had a problem.

At about 1:38am I am standing there pumping my gas eating some beef jerkey.Then at about 1:40am a truck with two men, pull up to the pump next to me.They head inside. No big deal right?   About 30sec later they both run out and have a bunch of beer. They were kinda jogging.   At this point,I realized what was happening.I pocket carry a glock 27(in a pocket holster). I reach in my pocket,and got a good grip.   So this is where i think i made the right call.   I didnt do anything,just stood there.They didnt come close to me and I didnt think I should risk all the bad things that could happen.   So they tossed the beer in the back of the truck and took off. The lady clerk ran out. She was talking on the phone and I think she got the plate number.I asked her if she had been robbed.   Of corse with all the stuff going on she didnt respond.   I got in my car and drove off.   What would you have done differently?   Sorry  end rant.

Power pistol.

I'm in for 2,000lbs @ 50¢ a lb. Would be nice to have that much.

Drv2fst. Its holds 45 .lr. It rattles too much for me. I'll get pics when I get home. And yes .920 barrels work I have to have the tapered barrel sleeves in now. The fake can is just to cove the ugly as stock barrel. And the fake can is plastic

I started with the Thumler's Tumbler. Its was a large cost at first but there's no dust and I don't have to replace the media. The inside rusted after a year,so I plasticoted it. The primer pockets also are super clean and small burs are removed. Its quite stunning to see the brass afterwards but case lube and handling dulls the cases. And I use a set lamp timer set it and forget it.

Hipower. I tryed to stock up before this bs happen. I had a lot more a year ago. Macgyver. I was going to get the red jacket zk22 but after the stunt they pulled I found this and waited a year to get. 87toy. Its got a lot of slop. Like glockish feel but I'm useto. I'm going to work on that later. I have yet too shoot it. Don't want to waste any .22

Here's more of the monitor. I have it where i can swing it outta the way,and use it to read reloading ebooks. [URL=https://imageshack.com/i/gheg1lj][/URL] [URL=https://imageshack.com/i/gvs3p8j][/URL] [URL=https://imageshack.com/i/5gmolrj][/URL] And also 'See' whats going on outside. [URL=https://imageshack.com/i/5srtmlj][/URL] [URL=https://imageshack.com/i/0uu6efj][/URL] [URL=https://imageshack.com/i/16w3hjj][/URL] [URL=https://imageshack.com/i/13bphbj][/URL] [URL=https://imageshack.com/i/1qqy6lj][/URL] [URL=https://imageshack.com/i/0suyg6j][/URL]

Here's mine its a work in progress. My first bench. I quickly outgrew. Here's the start of the new one. Its 3/4 MDF with 2x4 bracing this part is about 110lbs. This is it installed. Starting to build up. Good use from an extra battery Not done but getting closer.

High Tower Armory 90/22 Its a P90 conversion stock kit for a Ruger 10/22. This is my grab and gtfo kit Thanks for looking, if anyone has any questions ill be glad to try to help.

Power pistol for 9mm,40sw&10mm.

Under folder ak47 with surefire scout. Glock 23 with stream light tlr1s and night sights. Glock 27 with night sights (edc). Mag numbers my vary.

IOTV with soft inserts is my favorite so far.

I've also messed with blue dot,800x and aa9. In the 10mm and 7.62x25.

Longshot and Power Pistol are my  go two.

I do. I've saved up about 450 cases. I got everything to powder coat cast boolits for the ak. AA1680 is my flame of choice.

I got 3 boxes. Shot 1 today.

I allways get worried loading for the 7.62x25tok. Because there's no real load data,for the powders I'm testing.

I use the cleaning brush that was in the glock box. It reaches allmost everywhere needed.

G20 gen4

In for a total mag pic.

621

Nosler  180gr jhp 9.5gr Longshot 1.250 oal cci 300 lp 10 shot average   1295.3   Lee .401 mold using ww drops at 170gr 9.0gr longshot 1.255 oal cci 300 lp 10 shot average    1299.7

http://www.youtube.com/watch?v=H-PszuLwEu8&feature=youtube_gdata_player

I run my 40sw and 10mm brass through a lee fcd and lee bullet sizing container. Just remove the screw in part of the fcd place the bullet container on top and use the bullet "pusher" in place of the shellholder. I have ran +5 reloades on brass done this way no problems