RED333

I say take 6 shooters or better yet muzzle loaders, make things "fair".

Winchester 12 ga pump and yes I still have it.

Where is the kitchen sink? Nice job, keep the pics coming.

and with a bit of doing make a fixture to hold the stamps as a unit to keep things neat.

This is what was causing the noise in the trunk, not the dog he is mine.

I have a right side upper, upper is all I have, no bolt, barrel nothing. I have not built it yet. I was going to see if I could make a 40 S&W but picked up a 40 rifle that takes Glock mags. I will do something with it one day.

Did you expect any thing else, after all it is Chit car go.

I want to see them as well.

Well never did say just one firearm.

Well it showed up today and the pics do not do the knife justice at all. The fit and finish is just outstanding. As with all the knifes that GT makes.

is about all I can say.

The issue has been getting them to feed, I do not have a break open shorty. So I have not tried them.

metalsupermarkets.com 429 Enos Reed Dr, Nashville, TN 37210 (615) 256-9787

Thanks myg30, I did load up a few shot shell pistol loads, 44 mag and 45 Colt. Went into Gander 2 times, neither time did they what I needed, that was way before the "close out"'

I have had one with 308 factory ammo in a semi, caught it. One in 44 mag with my reloads, in a semi rifle, caught it. 4 in a 22LR revolver, caught it after the 4th round, PIA to get the bullets out of the barrel. It happens to us all, glad things work out for the good.

Welcome back, yep we are a mess, clean us up a bit?

Thanks,the hole is .020, I can barley see it with my glasses on. Yes, with bigger drippers, #6 can be made like this. Lead is clip on WW. This was more of a test, I wanted to use electric power, not gas. I did this in my reload room, I do have a power vent to keep air moving away from me. Thanks, look up shot drippers on youtube, been going on for years. The shot towers are a lost art for sure.

Yep I did it, been working on this for a few weeks. Picked up the pan and drippers from ebay. Coolant is cheap wally world fabric softener. Ammo cans stacked so the ramp is just clear of the coolant, large can to catch the over flow of coolant. I am using an electric stove top element and mapp torch to get things going and to keep the drippers flowing. The drippers will cool a bit and the torch keeps them warm. I made 5 lbs in about 30 mins, not bad for 3rd try. Size is 7 to 9 shot, some 11.

You gona share?

I picked up a little 5 shot 32 revolver, derringer, pocket pistol. It is a hoot to shoot with 10 grans of BP.

In a new movie the dead fly!!!

green Dot is about full as well, cycles my pistols well. That is spelled "boolits" to you sir!!! You are right smaller than a finger nail.

Yes it is a little round, 40 to 50 grans boolit, .5 to 1.5 grans of powder. Shell not much bigger than a 22 LR, and the small pistol primer fills the back end of the case. I cast for the little thing as well, a bit tedious at times, heck all the time. All that said I cast, powder coated and loaded a few this week end. I have 2 molds, a RCBS 25-50-RN, it drops a 50 gran boolit at .254, good looking boolit 2 at a time. The 2md ,mold a MeHic 25 HP that drops 3 at a time at 45 grans and .251. The green ones are the RCBS and the gray are the HP boolits. Since my powder measure will not drop less that 2.5 grans I made dippers, the top one is .5 for titegroup, the right one is 1.3 for green dot, the left was a test. Testing was good, no miss-feeds and hit a paper plate at 10 and 15 feet, with a less then 3 inch barrel I dont shoot out past 20 feet. It is a perfect round for getting varmints out of the chicken pen.

I have been known to pull and open my auto knife, to clean my nails and such. Is that "brandishing"?

Until you hear from the TBI you are just guessing. Could be the prints are unreadable or yours match close to a bad guy.